description. This series of fixed-voltage integrated-circuit voltage regulators is designed for a wide range of applications. These applications include on-card. 78L12 Positive-voltage Regulators. 3-Terminal Regulators Output Current mA No External Components Internal Thermal-Overload Protection Internal. TO CJ78L CJ78LTA. MARKING. Solid dot Green molding compound device,. XXX Code. CJ78L12 Device code if none,the normal device. CJ. 78L

Author: Kilmaran Felabar
Country: Laos
Language: English (Spanish)
Genre: Health and Food
Published (Last): 4 March 2008
Pages: 262
PDF File Size: 3.3 Mb
ePub File Size: 9.33 Mb
ISBN: 237-6-96985-541-5
Downloads: 57747
Price: Free* [*Free Regsitration Required]
Uploader: Gardabei

One of these regulators can deliver up to mA. Transformer in this package create a lot of manufacturers.

78L12 Datasheet

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Please check with an NEC Electronics sales representative for availability and additionalchange without notice.

In addition, they can be used with power-pass. A is a linear regulator, and does not step up the input voltage if the input is below the output for that you need a DC-DC boost regulator.

No abstract text available Text: Next we continue with connectors, transformer and big capacitors. How does it go from a Maximum dropout voltage eatasheet a minimum input voltage?

V VV to 20 V I. So the 20V delivers 20W, while the datasheer only consumes 12W. Darasheet you won’t find a parameter “minimum input voltage”, but it is mentioned as a condition for proper operation within certain limits. Allied Electronics DigiKey Electronics.


Home Questions Tags Users Unanswered. They are like a variable series resistor between input and output, causing a voltage drop across the regulator. A SIZE i 0. Please check with an NEC Electronics sales representative fordesign-in, refer to the latest publications of NEC Electronics data sheets or data books, dayasheet.

I tried to design them symmetrically. That means that when your load consumes 10W the switcher will only dissipate 1W. I built stereo width controller and i required simple dual power supply for him. These applications include on-card regulation for elimination of noise and distribution problems associated with single-point regulation.

Please check with an NEC Electronics sales representative. In addition, they can be used with power-pass elements to make high-current voltage regulators. Circuit description Circuit has on the primary side only fuse.

On the secondary side of transformer are connected two fuses mA and after them is bridge rectifier. I’ve seen LDOs with a dropout voltage of 50 mV. The internal limiting and. Please check with an NEC Electronicschange without notice.

78L12 Datasheet

Almost all components are usually available. All characteristics are measured with a 0. From what i understand then from your answer This series of fixed-voltage integrated-circuit. This is a snapshot of page When we use LEDs with a small current 2mA that we can use bigger resistors about daatasheet.


A note on dissipation: We begin with resistors, small capacitors, leds, regulators, fuses and rectifier. NEC Electronics assumes no responsibility for any errors that may appear in this document. One of these regulators can deliver up to mA of output current.

The internal limiting and thermal-shutdown features of these regulators make them essentially immune to overload. Peter Mortensen 1, 3 14 Dean 4, 22 57 If voltage on the big capacitors will be under Previous 1 2 From the above it may look like you best make your input voltage a lot higher than the 12V output, but that’s not true.

78L12 Datasheet

Next are positive and negative voltage regulators 78L12 and 79L12 with decoupling capacitors C3 to C6 close to regulators. Beware datashset polarity of electrolytic capacitors and orientation of diodes and regulators. All linear regulators have a minimum dropout voltageor difference. These applications include on-card.

We can also use 2 pin connectors for LED connecting. For signaling of presence of voltage is enough only one LED.