ASTM A991 PDF

ASTM A – Designation: A /A M – 98 (Reapproved ) Standard Test Method for Conducti. Purchase your copy of ASTM A/AM – 17 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. This standard is issued under the fixed designation A/AM; the number This test method is under the jurisdiction of ASTM Committee A01 on Steel, 2.

Author: Akigul Vokazahn
Country: Niger
Language: English (Spanish)
Genre: Environment
Published (Last): 27 September 2007
Pages: 81
PDF File Size: 5.42 Mb
ePub File Size: 9.4 Mb
ISBN: 998-5-80819-292-6
Downloads: 78092
Price: Free* [*Free Regsitration Required]
Uploader: Faezahn

All other conditions described in 6. It is the responsibility ast, the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier.

ASTM A991/A991M – 17

This method is used to determine the capability of the furnace to meet the permissible temperature variation specified in the applicable product specification, or as agreed to by the purchaser and supplier of heat treat services. A number in parentheses indicates the year of last reapproval.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Historical Version s – view previous versions of standard. Use of representative material to simulate product during survey is permitted.

Combining values from the two systems may result in non-conformance with the standard.

ASTM International – Standard References for ASTM A / AM – 17

Results of the application of this test method shall be expressed as a variation from a temperature set point. Within the text, the SI units are shown in brackets. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Link to Active This link will always route to the current Active version of the standard. For proposed working zones greater than, or equal to, 12 in. It provides validation of temperature uniformity by a series of tests rather than a single test.

  HYPSIBOAS CREPITANS PDF

Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are de? The rate of conveyance shall be representative of asym operating conditions. Attach survey test sensors to, or set them in the load.

Examples of these surveying techniques are listed below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

A major furnace modi? The working zone may be comprised of a919 or more heating zones in the furnace. In each test, determine the temperature variation pattern at one or more of the test locations.

AMS Pyrometry3 3. Interpretation of Results and Establishment of the Working Zone 9. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Furnace Survey Equipment 5. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier. Current edition approved Oct. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements. Place them at the outer extremities, the center of the proposed working zone, and in areas of suspected variability in the proposed working zone.

  CAMELOT 30K PDF

Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are defined in this test method. Heat Treatment in the Working Zone Originally approved in Starting time and chart speed shall be marked on the original temperature charts, 8. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements. Details of this procedure shall be as agreed to between purchaser and supplier.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Calibration to such national standards shall be done at least once every two years. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Documentation of Survey Results 8. This method is used to determine the capability of the furnace to meet the permissible temperature variation speci?