This User’s Manual describes how to use the E5EK compact, high-function digital Nevertheless, OMRON assumes no responsibility for errors or omissions. E5EK-AA Omron Automation and Safety Controllers 1/8 DIN VAC Digital field config datasheet, inventory, & pricing. This product was manufactured at OMRON Okayama. OMRON Okayama has obtained approvals from international certification bodies for its quality system and.
|Published (Last):||20 March 2017|
|PDF File Size:||9.78 Mb|
|ePub File Size:||20.92 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 39 setup mode. No part of this publication may be reproduced, stored in a retrieval system, or trans- mitted, in any form, or by any means, mechanical, electronic, photocopying, recording, recording, or other- wise, without the prior written permission of OMRON.
Page 84 PID control, standard con- trol or heating and cooling control. The heater burnout alarm is always OFF if the alarm is set to 0. In an open status, only control output 1 is ON. Set Point Limiter However, note that when the set point limiter is reset, the set point is forcibly changed to the upper-or lower-limit value of the set point limiter if the set point is out of the limiter range.
Comments to this Manuals Your Name.
For details on how to use the controller and parameter settings, see Chapters 2 onwards. F Operation at Both control output functions and alarm output functions operate.
D Setting up the E5EK PID control, standard con- trol or heating and cooling control. In this mode, you can set the communications conditions, transfer output and event input parameters to match the type of option unit set in the controller.
OMRON E5AK / E5EK Digital Controller
Page setup mode can be used. Multi-SP mode are used. When the value on the No. F Do not cover the area around the E5EK.
Use this end code to remedy errors that may occur. If you select the desired mode using the By pressing ‘print’ button you will print only current page. Page Stable range Set to Be sure to turn on the power supply to the load either before or simultaneously with the imron of Temperature Controller opera- omrn.
This example describes how to calibrate voltage input when the trans- fer output function is supported. Set value Input Type Page The display changes to [ ] 0mA calibration display. Setting Up The Output Unit 2. About The Communications Function 1. Page 70 On the E5EK controller, only parameters that can be used are omfon.
Function PV before passing through filter PV after passing through filter 0. A nega- tive setting sets an overlap band. E5ej ever, note that terminal Nos. How To Use Transfer Output 4. In this case, operation is carried out with the process value regarded as the set point before the change was made. The display changes to the menu display.
The set point during SP ramp is enabled only when the SP ramp function is enabled. The display changes to the menu dis- play. To exit this mode, press the key for 1 second minimum.
When another mode is selected while in these modes, reset is canceled. LBA, 7 to 9: Of these, only the alarm assigned as the output can be used. If the heater power supply is turned conditions ON after turning the E5EK power supply On, the heater burnout alarm is output. Setting Output Specifications Error 3; RSP input error With control output coolthe conditions for switching from standard control to heating and cooling control are reached when the output function is assigned at the cooling side during heating and cooling control.
In HT hunting tuning mode, when hunting occurs, the PID constants are amended to suppress the hunting. To print the manual completely, please, download it.
If the communications function is required, add on the communications unit. For details of operation at an alarm, see page For details on the setting ranges of these parameters, see chapter 5 Level 1 Mode page e5dk G5-series with omrln ethercat communications linear motor type pages. However, note that when thermocouple R, S, E, B, W or PLII is used, the cold junction compensator and the compensating conductor can be substi- tuted with the cold junction compensator and the compensating con- ductor for thermocouple K.
Press key to return the display to [ F Calibration: The E5EK controller is calibrated before shipment from the factory.
Omron E5EK-AA Processor/Controller | eBay
The functions of this key change according to how long it is pressed. The following figure shows the required device connection. Page 73 If this mode is switched to during auto-tuning, auto-tuning is canceled.
Specifications Assign these output functions to control output 1, control output 2, auxiliary output 1, w5ek auxiliary output 2. F Meaning Calibration data is in error. Conventions Used in this Chapter