HCNW3120 DATASHEET PDF

HCNW datasheet, HCNW pdf, HCNW data sheet, datasheet, data sheet, pdf, Agilent (Hewlett-Packard), Amp Output Current IGBT Gate Drive. Broadcom HCNW available from 7 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and availability. HCNW datasheet, HCNW circuit, HCNW data sheet: HP – Amp Output Current IGBT Gate Drive Optocoupler,alldatasheet, datasheet.

Author: Telrajas Meztikree
Country: Oman
Language: English (Spanish)
Genre: Video
Published (Last): 13 February 2005
Pages: 346
PDF File Size: 19.80 Mb
ePub File Size: 14.95 Mb
ISBN: 124-9-93347-227-8
Downloads: 49882
Price: Free* [*Free Regsitration Required]
Uploader: JoJozshura

In this test, VOH is measured with a dc load current. These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. To minimize dead time in a given design, the turn on of LED2 should be delayed relative to the turn off of LED1 so that under worst-case conditions, transistor Q1 has just turned off when transistor Q2 turns on, as shown in Figure The high operating voltage range of the output stage provides the drive voltages required datashest gate controlled devices.

Contact your Avago Technologies sales representative or authorized distributor for information. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. Note that the propagation delays used to calculate PDD and dead time are taken at equal temperatures and test conditions since the daatsheet under consideration are typically mounted in close proximity to each other and are switching identical IGBTs.

Temperature Figure 3 VOH vs. Figure 33 is an alternative drive circuit which, like the recommended application circuit Figure 25does achieve ultra high CMR performance by shunting the LED in the off state. For the continuous voltage rating refer to your equipment level safety specification or Broadcom Ltd. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards.

  CATALOGUE PARTYLITE 2008 PDF

Lab 9 in this note. This results in lower peak currents more margin than predicted by this analysis. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not datasheef interpreted as an input-output continuous voltage rating.

The thermal resistance values given in this model can be used to calculate the temperatures at each node for a given operating condition. When negative gate drive is not used VEE in the previous equation is equal to zero volts. Device considered a two-terminal device: For creepage, the shortest distance path along the surface of a printed circuit board dxtasheet the solder fillets datashet the input and output leads must be considered.

This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for a shielded optocoupler. Option data sheets are available. Contact an Avago Technologies sales representative or authorized distributor.

HCNW3120 Datasheet

Documents Flashcards Grammar checker. Maintenance of the safety data shall be ensured by means of protective circuits.

Techniques to keep the LED in the proper state are discussed in the next two sections. This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below the threshold during a transient. Data subject to change.

  ARYABHATTA MATHEMATICIAN BIOGRAPHY PDF

Pins 1 and 4 need to be connected to LED common. The LED is optically coupled to dxtasheet integrated circuit with a power output stage. To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry.

HCNW Datasheet(PDF) – AVAGO TECHNOLOGIES LIMITED

There are recommended techniques such as grooves and ribs which may be used datashdet a printed circuit board to achieve desired creepage and clearances. AVEN — March 21, All other brand and xatasheet names may be trademarks of their respective companies.

Dead time is the time period during which both the high and low side power transistors Q1 and Q2 in Figure 25 are off. See Applications section for additional details on limiting IOH peak. Any overlap in Q1 and Q2 conduction will result in large currents flowing through dagasheet power devices between the high and low voltage motor rails.

Minimum External Tracking L Creepage 7. Delaying the LED signal by the maximum propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the maximum dead time will be. However, this shield does not eliminate the capacitive coupling between the LED and optocoupler pins 5—8 as shown in Figure